TekBox TBOH01 LISN DC - CISPR 25 5µH
TekBox TBOH01 5µH LINE IMPEDANCE STABILISATION NETWORK LISN - CISPR 25
The TBOH01 5µH LISN is a device required to setup conducted noise measurements of DC-powered devices. It is designed to be used for EMC pre-testing in the frequency range of 150kHz to 110 MHz.
The LISN is inserted into the supply line of the DUT (Device Under Test). Conducted noise which is present at the supply terminals of the DUT can be measured at the BNC connector using a spectrum analyzer or a measurement receiver. The source (supply) terminal and the DUT terminal are decoupled by a 5µH inductor.
- Frequency range: 100kHz – 110MHz (1GHz, see figure 4 in the manual)
- DC Resistance: 35 mΩ
- Maximum current: 10A
- Maximum source voltage: 200V
300kHz...100MHz, measured impedance of the 5μH LISN
Conducted noise measurements are typically conducted using a sheet metal as ground plane. The GND terminals of all involved devices are connected to the metal shield using short cables.
As the measurement will be conducted in lab, rather than in a shielded chamber, a background noise measurement should be carried out with the DUT switched off or disconnected in order to be able to differentiate between conducted noise spectrum and background electric smog.
The picture below shows a typical conducted emissions measurement setup, such as specified in CISPR-25 standard. Setup details will differ depending on the type of DUT and applicable standards. For example, if the DUT has a vehicle power return line shorter than 200 mm, one LISN is inserted into the positive supply line. If the vehicle return line of the DUT is longer than 200 mm, two LISNs are required. One for the positive supply line and one for the power return line.
Example setup for a conducted noise measurement of a DC powered device
- - -
The screenshot above shows the result of a CISPR 25 conducted noise measurement of a DC/DC converter carried out with two TBOH01, a Rigol DSA815 and the Tekbox PC SW EMCview. With reference to the CISPR 25 limits, the measurement result shows compliance with Class 5 limits.
Example: conducted emissions, pre-compliance measurement of an automotive LED driver using two LISNs
Batter Fly s.r.l. is an Italian company established in 2002 with VAT number IT02235301203
Main contacts: telephone +39 051 6468377 email firstname.lastname@example.org
The address of our headquarters is Via Collodi 7a, 40012 Calderara di Reno (BO) Italy
All shipments depart from the address of our office indicated above by express courier unless otherwise specified in the order confirmation
For customers resident in Italy, both private and corporate, we apply the VAT of 22%
If the customer has specific VAT exemptions, he must communicate this before issuing the purchase order
For private customers residing outside Italy but within the European Union we apply the VAT of the country of destination
For corporate customers residing outside of Italy but within the European Union we do not apply VAT. However, VAT may be applied in the event that the customer enters an incorrect or non-certified VAT number by the VIES system
Customers can send purchase orders either through the website or by requesting a personalized quote using the specific form or through our main contacts indicated above
Batter Fly has been present for years within the MePa, the electronic market of the public administration. If one or more products are not present, contact us and we will load what is necessary quickly
Product availability is indicated on the product page of interest in various ways:
- Units in stock: 1 or more | indicates the actual units available
- Units in stock: 0, std delivery. 2 weeks | indicates the standard weeks that the supplier indicates for procurement
- Units available arriving on 10/24/2022: 3 | indicates that there will be available units arriving on that data
Products ordered before 3pm are shipped the same day, orders received after 3pm will be shipped the next working day
Each shipment is associated with a tracking number that will be communicated via email to the customer after taking charge by the shipper
To see the shipping costs go here https://www.batterfly.com/shop/consegna
To see the payment methods go here https://www.batterfly.com/shop/pagamenti
For any other questions please contact us through our main contacts