EA Elektro Automatik PS 9360-15 1U, 360V, 15A, 1500W alimentatore da laboratorio

EA Elektro Automatik PS 9360-15 1U, 360V, 15A, 1500W alimentatore da laboratorio

EA-PS 9000 1U 1500 W / 3000 W PROGRAMMABLE LABORATORY DC POWER SUPPLIES

- Wide input range 100...264 V (1500W models)
- High efficiency up to 95%
- Output power ratings: 0..1500 W or 0...3000 W
- Output voltages: 0...40 V up to 0...750 V
- Output currents: 0...6 A up to 0...100 A
- Flexible, power regulated output stage
- Various protection circuits (OVP, OCP, OPP, OTP)
- Control panel with pushbuttons and blue LCD for actual values, set values, status and alarms
- Remote sensing
- Share bus for support of parallel connection
- Galvanically isolated, analog interface with
  • U / I / P programmable via 0...10 V or 0...5 V
  • U / I monitoring via 0...10 V or 0...5 V
- Very low height of only 1 U (44 mm)
- Temperature controlled fans for cooling
- Discharge circuit (U out < 60 V in ≤ 10 s)
- USB and Ethernet port integrated
- EMC according to EN 55022 Class B
- SCPI command language supported
 

model Voltage Current Power Efficiency Ripple U max. Ripple I max. U Prog. res. I Prog. Res.
PS 9080-50 1U 0 - 80V 0 - 50A 0 - 1500W =<91% 100mVpp / 5.2Vrms 4mArms 3mV 2mA
PS 9200-25 1U 0 - 200V 0 - 25A 0 - 1500W =<93% 293mVpp / 5.1mVrms 8mArms 8mV 1mA
PS 9360-15 1U 0 - 360V 0 - 15A 0 - 1500W =<94% 195mVpp / 33mVrms 1.6mArms 14mV 0.6mA
PS 9500-10 1U 0 - 500V 0 - 10A 0 - 1500W =<94% 293mVpp / 63mVrms 1.4mArms 20mV 0.4mA
PS 9750-06 1U 0 - 750V 0 - 6A 0 - 1500W =<95% 260mVpp / 40mVrms 0.6mArms 30mV 0.25mA
PS 9080-100 1U 0 - 80V 0 - 100A 0 - 3000W =<92% 76mVpp / 4.2mVrms 6mArms 3mV 4mA
PS 9200-50 1U 0 - 200V 0 - 50A 0 - 3000W =<93% 234mVpp / 40mVrms 10mArms 8mV 2mA
PS 9360-30 1U 0 - 360V 0 - 30A 0 - 3000W =<93% 156mVpp / 26mVrms 1.9mArms 14mV 1.5mA
PS 9500-20 1U 0 - 500V 0 - 20A 0 - 3000W =<93% 234mVpp / 50mVrms 1.9mArms 20mV 0.8mA
PS 9750-12 1U 0 - 750V 0 - 12A 0 - 3000W =<93% 260mVpp / 40mVrms 0.7mArms 30mV 0.5mA


General
The microprocessor controlled laboratory power supplies of series EA-PS 9000 1U offer many functions and features in their standard version, making the use of this equipment remarkably easy and most effective. All this comes in a flat design with only 44 mm of height.
The clearly arranged control panel features two rotary knobs, six pushbuttons and two LEDs. Together with an illuminated, blue LCD display for all values and status it simplifies the use of the device.

AC input
All units are provided with an active Power Factor Correction circuit and models up to 1.5 kW are even suitable for a worldwide operation on a supply from 100 VAC up to 264 VAC.
Both power classes reduce the output power automatically when the input supply is low, so the 1.5 kW models can still provide 1 kW power with an input supply of 100...150 VAC and the 3 kW models can still provide 2.5 kW at 180...207 VAC.

Power
All models are equipped with a flexible auto-ranging output stage which provides a higher output voltage at lower output current, or a higher output current at lower output voltage, always limited to the max. nominal output power. The power set value is adjustable with these models. Therefore, a wide range of applications can already be covered by the use of just one unit.

DC output
DC output voltages between 0...80 V and 0...750 V, output currents between 0...6 A and 0...100 A and output power ratings of 0...1500 W or 0...3000 W are available.
Current, voltage and power can thus be adjusted continuously between 0% and 100%, no matter if manually or remotely controlled (analog or digital).
The DC output is located on the rear panel of the devices.

Discharge circuit
Models with a nominal output voltage of 200 V or higher include a discharge circuit for the output capacities. For no load or low load situations, it ensures that the dangerous output voltage can  sink to under 60 V DC after the DC output has been switched off. This value is considered as limit for voltages dangerous to human safety.

Protective features
For protection of the equipment connected, it is possible to set an overvoltage protection threshold (OVP), as well as one for overcurrent (OCP) and overpower (OPP). As soon as one of these thresholds is reached for any reason, the DC output will be immediately shut off and a status signal will be generated on the display and via the interfaces. There is furthermore an overtemperature protection, which will shut off the DC output if the device overheats.

Display and controls
All important information is clearly visualised on a dot matrix display.
With this, information about the actual output values and set values of voltage and current, the actual control state (CV, CC, CP) and other statuses, as well as alarms and settings of the setup menu are clearly displayed. In order to ease adjusting of values by the rotary knobs, pushing them can switch between decimal positions of a value. All these features contribute to an operator friendliness. With a panel lock feature, the whole panel can be locked in order to protect the equipment and the loads from unintentional misuse.

Analog interface
There is a galvanically isolated analog interface terminal, located on the rear of the device. It offers analog inputs to set voltage, current and power from 0...100% through control voltages of 0 V...10 V or 0 V...5 V.
To monitor the output voltage and current, there are analog outputs with voltage ranges of 0 V...10 V or 0 V...5 V. Also, several inputs and outputs are available for controlling and monitoring the device status.

Digital interfaces
All models features two galvanically isolated, digital interfaces by default. These are 1x USB and 1x Ethernet. Both can be used to control and monitor the devices with SCPI language commands or Modbus protocol.
Remote control of a device can be done either by the included software EA Power Control or by a custom application, which is supported by a programming documentation, as well as LabView™ Virtual Instruments (VIs).

Scrivi una recensione

Nota: Il codice HTML non viene tradotto!
    Male           Buono
Captcha
  • Visualizzazioni: 2488
  • Marca: EA Elektro Automatik
  • Codice Prodotto: 06230402
  • MPN: 06230402
  • Disponibilità: Ordinabile
  • Prezzo Netto:
  • 2.085,00€
  • Prezzo incl. 22% IVA: 2.543,70€

Tag: eaps90001u

Testimonials

È la seconda volta che faccio acquisti su Batter Fly ed il servizio è sempre eccellente: spedizione in tempi record e consegna velocissima. Il prodotto è esattamente quello che avevo ordinato e ...

Konstantin Erokhin sopra 19/02/2020

Ottimo servizio e pienamente soddisfatto dell'acquisto Nello Staff di BatterFly ho trovato professionalità e cortesia. Grazie

Lorenzo M sopra 17/02/2020