-
U heeft nog geen producten in uw winkelwagen.
U heeft nog geen producten in uw winkelwagen.
The PicoScope 6000E Series fixed-resolution and FlexRes® oscilloscopes provide 8 to 12 bits of vertical resolution, up to 1 GHz bandwidth and 5 GS/s sampling rate with active probes to match
Four or eight analog channels have the timing and amplitude resolution you need to reveal signal integrity issues such as glitches, runts, dropouts, noise, distortion and ringing. 16 digital MSO channels enable the debug and verification of complex ECUs and FPGA-based designs.
These new oscilloscopes are ideal for design engineers working on high-performance embedded systems, signal processing, power electronics, mechatronics and automotive designs, and for researchers and scientists working on multichannel high-performance experiments.
More
4/8 analog +
16 digital
channels (MSO)
Deeper
Up to 4 GS
memory
Higher
Up to 1 GHz
bandwidth
Smarter
8-bit and
8/10/12-bit
FlexRes®
architecture
Better
Active
probes with
Intelligent
Probe Interface
Most
21 serial
protocol
decoders as
standard
PicoScope 6000E Series applications
Embedded system debug in
the laboratory
PicoScope 6 software with
support for multiple monitors
PicoScope 6000E used in power
systems analysis
Digital systems debug
and verification
OEM and custom
applications
Scientific research
and education
Take a closer look at the PicoScope 6000E Series
PicoScope 6 included
Time and frequency domain displays
Advanced triggering capabilities
50 MHz function generator and AWG
Serial data decoding and analysis: 21 protocols included as standard
Automated waveform measurements
Digital channels displayed individually or grouped as a bus
Mask limit testing
Properties panel shows instrument settings at a glance
| Model | BW (MHz) | Channels | Resolution (bits) | Memory (GS) |
|---|---|---|---|---|
| 6824E | 500 | 8 | 8 to 12 | 4 |
| 6424E | 500 | 4 | 8 to 12 | 4 |
| 6804E | 500 | 8 | 8 | 2 |
| 6404E | 500 | 4 | 8 | 2 |
| 6403E | 300 | 4 | 8 | 1 |
| 6426E | 1000 | 4 | 8 to 12 | 4 |
| 6425E | 750 | 4 | 8 to 12 | 4 |
| 6406E | 1000 | 4 | 8 | 2 |
| 6405E | 750 | 4 | 8 | 2 |
| TA369 MSO 8-channel pod: €599 each | ||||
| A3076 750 MHz active probe kit: €959 each | ||||
| A3136 1.3 GHz active probe kit €1205 each | ||||
A3000 Series active probes with Intelligent Probe Interface
The Pico A3000 Series are high-impedance active oscilloscope probes. They have been designed to have minimal impact on the signal being probed with maximum signal transfer to the PicoScope 6000E Series via the intelligent probe interface.
Their ergonomic design allows for comfortable handheld use with the addition of a button to start and pause capturing in PicoScope 6.
The intelligent probe interface powers the probe from the scope and automatically sets the scope’s scaling and input impedance to match the probe.
With an input resistance of 1 MΩ and capacitance of 0.9 pF, these active probes offer high input impedance into the GHz range.
TA369 MSO Pod
The detachable active MSO pod is powered by the scope and connects to either of two digital interface ports on the front panel, with eight permanently attached flying leads terminating in MSO probes.
The detachable active MSO pod is powered by the scope and connects to either of two digital interface ports on the front panel, with eight permanently attached flying leads terminating in MSO probes.
Probe Positioning System
The Pico oscilloscope probe positioning system holds your circuit board firmly during soldering, inspection and test.
For testing, the kits are supplied with probe holders which secure magnetically to the steel base plate.
When the probes are installed in the holders they can be positioned to make contact with points of interest on the circuit board and will remain in contact while you make measurements.
The large steel base plate is mirror finished allowing you to see any items such as status LEDs underneath the PCB.
Leave a Comment