| Model |
Code |
Features |
| Standard cable FR |
200063 |
This 5 pin cable is supplied standard with any /FR screwdriver. Length: 2,5 m. |
| Standard cable TA |
250063/N |
This 8 pin cable is supplied standard with any /TA torque & angle screwdriver. Length: 2,5 m. |
| Tool balancers TECBA1 |
010300 |
New tool balancers TECBA1, code no. 010300, allow screwdrivers to be positioned over the work station for comfortable operation. Models with higher capacity available on request. |
| ARMPV1 support arms |
010500 |
ARMPV1 support arms, code 010500, consist of a vertical support on which a 180° pivoting arm is attached. |
| Double output connector DOCK01 |
020020 |
A double output connector is available for operators using two FAB or RAF screwdrivers in the same working area. One end is to be connected to the controller (cable included), the other end to the drivers. Screwdrivers not to be used at the same time |
| Double output connector DOCK02 |
020035 |
A double output connector is available for operators using two KBL..FR (not KBL..FR/CA nor KBL..FR/S) screwdrivers in the same working area. The screwdrivers can be used at the same time. |
| Double output connector DOCK02/S |
020035/S |
A double output connector is available for operators using two KBL..FR/S screwdrivers in the same working area. The screwdrivers can be used at the same time. |
| Double output connector DOCK04 |
020045 |
A double output connector is available for operators using two PLUTO screwdrivers with EDU2AE/TOP in the same working area. The screwdrivers cannot be used at the same time. |
| Double output connector DOCK04/TA |
020045/TA |
A double output connector is available for operators using two PLUTO screwdrivers with EDU2AE/TOP/TA in the same working area. The screwdrivers cannot be used at the same time. |
| Extension ring KP05 |
234511/K |
KP05, code 234511/K, is an extension ring to be used with Pluto inline drivers for easier clamping on reaction arms. |
| Angle Head FAB - ANG HD1 |
010100 |
When space is limited a right angle head can be easily attached to lever start FAB screwdrivers. ANG HD1 is the cost effective alternative to ANG HD8. 1/4” hex - max torque 6 Nm |
| Angle Head RAF - ANG HD2 |
010120 |
When space is limited a right angle head can be easily attached to lever start RAF screwdrivers. ANG HD2 is the cost effective alternative to ANG HD9. 1/4” hex - max torque 6 Nm |
| Angle Head FAB - ANG HD8 |
010143 |
When space is limited a right angle head can be easily attached to lever start FAB screwdrivers. Model ANGHD8, code 010143, is suitable to FAB series. 1/4” hex - max torque 6 Nm |
| Angle head RAF - ANG HD9 |
010144 |
When space is limited a right angle head can be easily attached to lever start RAF screwdrivers. Model ANGHD9, code 010144, is suitable to RAF series. 1/4” hex, coppia max 6 Nm |
| Socket tray for TOP unit |
020042 |
When using a multiple torque system a socket tray can be a useful accessory for program selection. It's very easy to use: the control unit automatically selects the correct preset program when a bit or socket is removed. |
| Switchbox for TOP unit |
020033 |
A switch box can be a useful accessory for multiprogram selection. It's very easy to use: each time a button is pushed, the control unit automatically selects the preset program. |
| KBL clutch cover |
020028 |
Coprifrizione per KBL04-15FR |
| KBL clutch cover |
020028/CA |
Clutch cover for KBL04-15FR/CA |
| KBL clutch cover |
020029 |
Clutch cover for KBL30FR |
| KBL clutch cover |
020029/CA |
Clutch cover for KBL30FR/CA |
| AC2.3 |
010113 |
Autocatcher for M2 to M3 screws.
The autocatcher is the easiest way to catch non-magnetizable screws. |
| AC3.5 |
010114 |
Autocatcher for M3 to M5 screws.
The autocatcher is the easiest way to catch non-magnetizable screws. |
| ACE Screw Counter |
020021 |
L’ACE Conta Viti è una scheda di controllo che consente di verificare l’esatto fissaggio delle viti calcolando in tempo reale il tempo impiegato dalla vite per essere fissata e verificando contemporaneamente che non vi siano viti mancanti nel pezzo. |
| ACE Screw Counter |
020022 |
The ACE screw counter is a process control system that monitors the fastening assembly process. It tracks, in real time, the fastening of each screw in an assembly, then notifies the result. |
| Telescopic Spindle |
800322 |
1/4" - 1/4"
max 7 Nm
PLUTO..FR/FN, MITO../FN, KBL../FN |
| Telescopic Spindle |
800319 |
1/2" - 1/2"
max 50 Nm
PLUTO..50/FN |
| Telescopic Spindle |
800320 |
1/4" - 3/8"
max 15 Nm
PLUTO3-6-10-15 |
| Telescopic Spindle |
800321 |
3/8" - 3/8"
max 35 Nm
PLUTO20-35 |
| Coloured Rings |
200085 |
Color: BLU
Coloured rings are useful to distinguish and identify different screwdrivers at a glance. |
| Coloured Rings |
200086 |
Colore: RED
Coloured rings are useful to distinguish and identify different screwdrivers at a glance. |
| Coloured Rings |
200087 |
Colore: YELLOW
Coloured rings are useful to distinguish and identify different screwdrivers at a glance. |
| Coloured Rings |
200088 |
Colore: GREEN
Coloured rings are useful to distinguish and identify different screwdrivers at a glance. |
| Coloured Rings |
200089 |
Colore: BLACK
Coloured rings are useful to distinguish and identify different screwdrivers at a glance. |
| Barcode reader BRCR90 |
020050 |
The BRCR90 barcode reader allows the operator to instantly select the program previously set on the control unit. To be used with EDU2AE/TOP or EDU2AE/TOP/TA. |
| Serial Printer PRNTR1 |
020026 |
The PRINTR1 serial printer gives the possibility to instantly print the results of each tightened screw. It works with EDU2AE/TOP, EDU2AE/TOP/TA, EDU2AE/HPRO control units and K and Mini K../S torque testers. |
| Cable with strain relief |
250063/H |
The cable with spring is more resistant thanks to a longer connector and spring, which makes the cable up to 4 times more endurable. Perfectly compatible with any 5 pin (code 200063/H) or 8 pin (code 250063/H) screwdriver/control unit. |
| Ethernet Device |
020075 |
Kolver Ethernet Device (code 020075) makes it possible to connect a PC to any EDU 2AE/TOP - TOP/E - TOP/TA via remote LAN connection. |
| Light stack |
020080 |
The light stack allows better visibility of output signals. Made for any control unit with signals. Supplied standard with 2,5m cable and 10pin connector for CN1 (EDU2AE - EDU2AE/TOP). Wiring for other Kolver control units available on request. |
| Start / Reverse Pedals |
020070 |
Start and reverse signals can now be activated using our new foot pedal. Supplied standard with 3,5 m cable and connector for any EDU2AE and EDU2AE/TOP unit. |
| Suction head A2 |
010111/1 |
A2 suction head for M2-M2,6 screws
The suction head is a very effective device that eliminates the manipulation of small and / or non-magnetizable screws (stainless steel, brass, plastic, etc.). Suitable for any screwdriver! |
| Suction head A3 |
010111/2 |
A3 suction head for M3-M4 screws
The suction head is a very effective device that eliminates the manipulation of small and / or non-magnetizable screws (stainless steel, brass, plastic, etc.). Suitable for any screwdriver! |
| Testina di aspirazione ASP HD6 |
010117 |
Suction head for NATO15
Small and / or non-magnetizable screws can be easily removed using the suction head. |
| Testina di aspirazione ASP HD7 |
010118 |
Suction head for NATO50
Small and / or non-magnetizable screws can be easily removed using the suction head. |
| ASP suction head HD8 |
010119 |
Suction head for MITO15
Small and / or non-magnetizable screws can be easily removed using the suction head. |
| ASP suction head HD9 |
010121 |
Suction head for PLUTO3-15
Small and / or non-magnetizable screws can be easily removed using the suction head. |
| Centering heads RIV HD1 |
010180 |
hole 8 mm
for PLUTO3D, PLUTO6D, PLUTO10D/N, PLUTO15D/N |
| Centering heads RIV HD2 |
010181 |
hole 8 mm
for KBL04FR and KBL15FR, also with signals (KBL..FR / S) and with autoreverse (KBL..FR / AR) |
| Centering heads RIV HD3 |
010182 |
hole 3 mm
for PLUTO3D, PLUTO6D, PLUTO10D/N, PLUTO15D/N |
| Centering heads RIV HD4 |
010183 |
hole 3 mm
for KBL04FR and KBL15FR, also with signals (KBL..FR / S) and with autoreverse (KBL..FR / AR) |
| Centering heads RIV HD5 |
010184 |
hole 3 mm
for KBL30FR and KBL40FR, also with signals (KBL..FR / S) and with autoreverse (KBL..FR / AR) |
| Reduced Front Ring for PLUTO |
234515 |
Inline PLUTO screwdrivers can be supplied with reduced front ring (code 234515). The new reduced front ring, code 234515, is also available as accessory/spare part and supplied with four M3x6 screws. |
| Support for angle head screwdrivers |
010176 |
To be installed on vertical sufaces to quickly store RAF and PLUTO angle screwdrivers. |
| Universal pistol grip support |
010175 |
To be installed on vertical surfaces to quickly store any Kolver pistol grip tool, including FAB, RAF, KBL, PLUTO and KDS models. |
| KDU Adapter kit with SW and CBS |
010410 |
Connect your KDU control unit to this KDU Adapter and select up to 8 programs or sequences via SWBX88 Switchbox or CBS880 socket tray. |
| Table stand for KDU |
010400 |
A table stand ensures quick access to cables when placing your KDU unit on a flat surface. It is the best option in case you’d like to keep your KDU controller right at hand. |
| Wall mount for KDU |
010401 |
Wall mounts can be easily installed on any vertical surface and allow KDU controllers to tilt up/down and left/right – place your KDU unit anywhere and adjust its position to best suit your needs. |
| 2.5 m Cable for K-Ducer |
250064 |
Connection cable between KDS screwdrivers and KDU controllers (M16, 10 pin). Length: 2.5 m |
| 5 m Cable for K-Ducer |
250564 |
Connection cable between KDS screwdrivers and KDU controllers (M16, 10 pin). Length: 5 m |
| 2.5 m Cable for K-Ducer, with spring |
250064/H |
Heavy duty connection cable between KDS screwdrivers and KDU controllers (M16, 10 pin). Length: 2.5 m |
| 5 m Cable for K-Ducer, with spring |
250564/H |
Heavy duty connection cable between KDS screwdrivers and KDU controllers (M16, 10 pin). Length: 5 m |
| Double output connector DOCK05 |
020046 |
A double output connector is available for operators using two KDS screwdrivers with one KDU controller in the same working area. The screwdrivers cannot be used at the same time. |
| UR-Mount |
010695/UR |
Tool holder for screwdrivers up to ∅37mm, to be attached to Universal Robots® robotic arm. Code no. 010695/UR for PLUTO3, 6, 10, 15CA and CA/FN2 | Code no.010695/URM for MITO | Code no. 010695/URN for any tool ∅19-37mm |
